Medium to Large Scale Charcoal & Biochar Production System
Many of my readers ask about how to make biochar or charcoal in bulk quantity instead of few kg per batch. In that case, you have to increase the size of the charcoal kiln or buy a professional production system.
I discovered that biochar.info produce biochar production systems. They offering pre-manufactured small to medium scale biochar kilns, as well as customized engineering plans that can be used to manufacture larger capacity biochar production facilities. Now I will introduce to you:
Horizontal Bed Biochar Reactor
The horizontal bed biochar reactor can be used for a variety of feedstocks, it has a pre-dryer, incorporates the ability to closely control process parameters of temperature and residence time, and can be flexibly configured to make use of the excess heat produced, and condense tars from the raw syngas. Capacity can be adjusted by increasing or decreasing the width and length of the unit, up to a maximum of about 4 tonnes of char produced per 24 hour day. Heat energy to dry and pyrolyse the feedstock is provided by flaring a portion the syngas produced (except at startup, where a separate gas source is needed). The unit requires a relatively small amount of electricity to run the blowers, feed mechanisms and control electronics.
Vertical Silo Biochar Reactor
The Vertical Silo Biochar Reactor is specifically designed to produce large quantities of biochar at low cost. In addition, it also produces a clean burning syngas (a combination of hydrogen, carbon monoxide, and methane), and byproducts of tar and wood vinegar if these are desired. The syngas can be used as a replacement for propane or natural gas, producing heat for poultry sheds or greenhouses for instance. It can also be used to generate mechanical energy for irrigation pumps via a heat exchanger and modern steam engine, or to generate electricity.
Our pyrolysis reactor is a continuous feed device that can economically process any type of relatively dry biomass waste into biochar and energy. The operating parameters can be adjusted to the temperature range or residence time desired. Hence the kiln can produce biochar of various qualities, or even torrefied biomass.
Our pilot model has a retort volume of about 5 cubic meters and can process upwards of 1 tonne of air-dried, chipped woody biomass per hour, including orchard or vineyard pruning waste, sugarcane bagasse, forestry or sawmill waste. Conversion efficiency of woody biomass to biochar is some 30 to 33 percent, so the unit will produce some 300 – 330 kilograms of biochar per tonne of biomass input. Straws and grasses have lower lignin content and hence a lower conversion efficiency to biochar, approximately 17% can be expected.
Each tonne of air-dried biomass processed will produce approximately 1.4 MWh to 1.7 MWh of chemical energy in the syngas produced. In the pilot model, the syngas is flared in a swirl burner above the unit.
If you are interested in learning more about our biochar technology, or simply want to follow our progress, please fill out the contact form below.
Tilting Batch Biochar Kiln
The tilting batch kiln is designed to produce biochar from sticks and split wood. The tilting mechanism allows for easy loading and unloading of the unit. It is also possible to configure 3 units in a round-robin fashion so that the excess heat from one is used to start the pyrolysis process in another. These units require no electricity, but there may be more manual labor involved in preparing the feedstock, loading and unloading.
Batch Kiln 100-MK 1
Simple and easy to use, this kiln has a cylindrical body 1.2 meters high and 1.5 meters in diameter. The kiln has an internal combustor (firebox) which hangs from the lid and provides heat to convert the feedstock to biochar. It takes about 8 hours for a batch to be processed, depending on the moisture content, type and size of the feedstock.
The kiln is loaded from the top, and unloaded through a door at the bottom. A hand-driven winch is used to remove the lid for loading. After a burn, the kiln is left overnight to cool before unloading. A single batch can produce up to 100 kg of biochar.
The kiln runs on a two stage cycle. First the feedstock is dried, then it is charred. The design relies on air convection to distribute heat throughout the feedstock bed. It is for this reason that feedstock is limited to split or small diameter wood. During the drying stage small logs are burned in the firebox to provide heat. As temperatures within the kiln rise to around 450 C, the feedstock releases syngas. Once syngas is available, it is burned in the combustor to maintain suitable charring temperatures.
The kiln is transportable on a small trailer. It is therefore likely that in most areas, planning permission would not be needed. It does however produce some steam and smoke, so it is advisable to locate it away from buildings and people. The kiln does not need electricity to run. It uses a leaf blower included with the kiln to supply air to the internal combustor.
Batch time: around 8 hours Moisture content: up to 40% Feedstock size: logs, up to 30 cm in length and 10 cm in diameter Feedstock type: Wood Feedstock volume: 1.5 cubic meters Fuel source: logs, up to 15 cm in length and 5 cm in diameter Char yield: up to 100 kg per batch Infrastructure used: handheld leaf blower (provided with the kiln) Price: ~ 7500 Swiss francs
The MK 2 is a small-scale biochar kiln capable of processing a wide range of different materials. Process temperatures can be controller to an accuracy of within 25 degrees C. These 2 factors combined make it an excellent choice for trials and research. As with the MK 1, the cylindrical body is 1.2 meters high and 1.5 meters in diameter, and it has an internal combustor (firebox) to provide the heat necessary to convert the feedstock to biochar.
The MK 2 has been tested on a wide range of feedstocks including wood shavings, woodchip, logs, rice husks, coffee husks, rush and wetland reed. The kiln can process feedstocks up to 60% moisture content. The length of a given batch varies significantly, depending on the moisture content, type and size of the feedstock used.
The kiln is loaded from the top, and unloaded through a door at the bottom. An electric winch is used to remove the lid for loading. After a burn, the kiln is left overnight to cool before unloading. A single batch can produce up to 100 kg of biochar.
The kiln runs on a two stage cycle. First the feedstock is dried, then it is charred. The kiln acts as a steam drier during the first stage, using 3 electric fans to force steam through the feedstock. One key factor as to whether a feedstock is suitable for use in the kiln is the porosity of the feedstock bed. The fans must be able to force the steam to flow through the material. During the drying stage small logs are burned in the firebox to provide heat. As temperatures within the kiln rise to around 450 C, the feedstock releases syngas. Once syngas is available, it is burned in the combustor to maintain suitable charring temperatures.
The kiln is transportable on a small trailer. It is therefore likely that in most areas, planning permission would not be needed. It does however produce some steam and smoke, so it is advisable to locate it away from buildings and people. The kiln does need electricity to run, however it is supplied with a suitable generator in case supply from the electricity grid is not available.
Batch time: from 3 to 10 hours Moisture content: up to 60% Feedstock size: wood shavings or rice husk, up to 30 cm length logs Feedstock type: most biomass Feedstock volume: 1.5 cubic meters Fuel source: logs, up to 15 cm in length and 8 cm in diameter Char yield: up to 100 kg per batch Infrastructure used: 3 electric fans and a generator (provided with the kiln) Price: ~ 25,500 Swiss francs
Batch Kiln 500-MK 1
The 500 series batch kiln is a commercial unit that produces up to 750 kg of biochar per burn. The kiln is built in to a 20 ft container which allows it to be transported anywhere a truck can reach.
The kiln consists of two kiln bodies (retorts) with a capacity of 6 cubic meters each, and a central combustor or burner that provides heat to both. The kiln uses a two stage process: the first stage dries the feedstock, while the second stage pyrolyzes the feedstock into biochar. The retorts are processed in alternate cycles so that excess heat from the active retort is used to dry the feedstock in the inactive retort (and possibly initiate pyrolysis if 24/7 operation is desired). In this way, the kiln reduces the external fuel requirements for the drying of feedstock, thus making the processing of wet materials much more viable.
If there is a gap in the symmetry of the process in which syngas is not available to produce needed heat, the central burner automatically reverts to burning woodchip. The central burner also burns woodchip to perform a cold start of the kiln until there is sufficient syngas being produced.
This kiln can process a wide range of feedstocks including wood shavings, woodchip, logs, rice husks, coffee husks, rush and wetland reed, up to 60% moisture content. The burn time can vary dependent on the moisture content, type and size of the feedstock used. Process temperatures can be controlled to an accuracy of within 25 degrees C.
Batch time: variable, up to 8 hours Moisture content: up to 60% Feedstock size: from rice husk, wood shavings and wood chip up 30 cm length logs Feedstock type: most types of biomass Feedstock volume: two kiln bodies or retorts of 6 cubic meters each Fuel source: woodchip Char yield: up to 750 kg per cycle (per 6 m3 retort) Infrastructure used: 4 electric fans and a generator (provided with the kiln) Price: ~75,000 Swiss francs excluding shipping
Here is contact info in case you wanna buy these charcoal/biochar making system:
I would like to speak to someone about building a system for large scale production of biochar. I am creating a soil company with a focus on education. and want to produce my own biochar.
will you please help?
hi to every body that having access to read this massage. I Tanzanian guy seeking to preserve environmental distraction which is highly occurred on the word surface and suddenly will tend to have a negative impacts to the world. Here I seeking to know how to made a charcoal from the wastes products instead of using treeses. Please I need a helper for this.